Rong Chang, Chunsheng Wang, Xiangqi Kong, Wenhui Li and Jinchun Wu. The role of second generation sequencing technology and nanomedicine in the monitoring and treatment of lower extremity deep vein thrombosis susceptibility genes. Bioengineered. 2021 Nov. doi: 10.1080/21655979.2021.2003926.Since publication, significant concerns have been raised about the compliance with ethical policies for human research and the integrity of the data reported in the article.When approached for an explanation, the authors provided some original data but were not able to provide all the necessary supporting information. As verifying the validity of published work is core to the scholarly record's integrity, we are retracting the article. All authors listed in this publication have been informed.We have been informed in our decision-making by our editorial policies and the COPE guidelines.The retracted article will remain online to maintain the scholarly record, but it will be digitally watermarked on each page as 'Retracted.'

The ability to track the levels of specific molecules, such as drugs, metabolites, and biomarkers, in the living body, in real time and for long durations, would improve our understanding of health and our ability to diagnose, treat, and monitor disease. To this end, we are developing electrochemical aptamer-based (EAB) biosensors, a general platform supporting high-frequency, real-time molecular measurements in the living body. Here we report that the use of an agarose hydrogel protective layer for EAB sensors significantly improves their signaling stability when deployed in the complex, highly time-varying environments found in vivo. The improved stability is sufficient that these hydrogel-protected sensors achieved good baseline stability and precision when deployed in situ in the veins, muscles, bladder, or tumors of living rats without the use of the drift correction approaches traditionally required in such placements. Finally, our implantable gel-protective EAB sensors achieved good biocompatibility when deployed in vivo in the living rats without causing any severe inflammation.

Vascular grafts are widely used for vascular surgeries, to bypass a diseased artery or function as a vascular access for hemodialysis. Bioengineered or tissue-engineered vascular grafts have long been envisioned to take the place of bioinert synthetic grafts and even vein grafts under certain clinical circumstances. However, host responses to a graft device induce adverse remodeling, to varied degrees depending on the graft property and host's developmental and health conditions. This in turn leads to invention or failure. Herein, we have mapped out the relationship between the design constraints and outcomes for vascular grafts, by analyzing impairment factors involved in the adverse graft remodeling. Strategies to tackle these impairment factors and counteract adverse healing are then summarized by outlining the research landscape of graft innovations in three dimensions-cell technology, scaffold technology and graft translation. Such a comprehensive view of cell and scaffold technological innovations in the translational context may benefit the future advancements in vascular grafts. From this perspective, we conclude the review with recommendations for future design endeavors.

This study presents a biomimetic 3D customizable artificial vascular graft with a highly porous and uniform microscale structure. The structural features were obtained by dip coating of a highly close-packed microsphere suspension on a 3D printed sacrificial template. Considering the structured arrangement of microspherical porogens in the coating layer, the microsphere-leached constructs showed higher uniformity and porosity than the conventionally particulate-leached structures, leading to ultrasoft mechanical compliance. Considering biomechanical compatibility, the resulting elastic moduli were at the sub-MPa level, comparable with those of native vascular tissues. In addition, the developed porous graft was reinforced selectively at the edge regions using a nonporous coating to secure its practical sutureability for clinical use. The sufficiently low cytotoxicity was clinically confirmed to alleviate the stiffness mismatch issues at the anastomotic interface between the native tissue and the artificial graft, thus overcoming the relevant clinical complications. Furthermore, the overall superior properties could be implemented on the 3D printed template for patient-specific medicare, thus implying the manufacturability of patient-specific vascular grafts.

Nanochemotherapy is recognized as one of the most promising cancer treatment options, and the design of the carrier has a crucial impact on the final efficacy. To precisely improve the efficacy and reduce the toxicity, we combined the clinical contrast agent (Gd-DTPA) with a stimulus-sensitive o-nitrobenzyl ester and then prepared a series of nNBGD lipids by varying the carbon chain length of the hydrophobic group. The self-assembled nNBGD liposomes can be tracked by MRI to localize the aggregation of drug carriers in vivo, so as to prompt the application of light stimulation at the optimal time to facilitate the precise release of carriers at the lesion site. And the application potential of this strategy was verified with 88% tumor suppression effect in the 12NBGD-DOX+UV group. In addition, this paper emphasizes that small differences in structure can affect the overall performance of the carriers. By exploration of the differences in stability, drug loading, stimulus responsiveness, MRI imaging effect, and toxicity of the series of nNBGD carriers, the relationship between the length of the hydrophobic group of nNBGD lipids and the overall performance of the carriers is given, which provides experimental support and design reference for other carriers.

Oil spills in the ocean greatly threaten local environments, marine creatures, and coastal economies. An automatic water/oil separation material system was proposed in this study, and a tubular geometry was chosen to demonstrate the water/oil separation efficiency and effectiveness. The water/oil separation tubes were made of expanded polytetrafluoroethylene (ePTFE) and graphite composites. The permeation pressures of water and oil through the tube walls were tuned by adjusting the ePTFE microstructure, which, in turn, depended on the degree of expansion and the graphite content. Fourier-transform infrared spectroscopy was performed to confirm the compositions of the ePTFE/graphite composites, and a scanning electron microscope was used to examine the microstructure and morphology of the expanded PTFE/graphite composite tubes. When a proper pressure was applied, which was higher than the oil's permeation pressure (3.0 kPa) but lower than the water's permeation pressure (57 kPa), the oil leaked out of the tube walls while the water went through the ePTFE/graphite tubes. As such, the water/oil mixture could be separated and collected in different containers or an outer tube. Due to this automatic separation, the whole process could be done continuously and conveniently, thus exhibiting great potential in the practical applications of oil spill and water separation/remediation.